Plumbing for Beginners: The Essentials for Bathtub Installation
Plumbing for Beginners: The Essentials for Bathtub Installation
Blog Article
This article which follows about How to Install a Bathtub is definitely captivating. Read it for your own benefit and see what you think of it.
Installing a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, and often, tiling abilities. Changing an old bathtub with a new one is additionally a moderately hard job. If the old bathtub is readily accessible, the job can relocate rapidly; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will need a helper to leave the old tub as well as embeded in the brand-new one. Make certain you have actually certified yourself for the task as well as are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed job, it is far better to take into consideration using one before you begin. Opportunities are you might require a professional plumber to make tube connections.
This write-up will certainly assist you set up a new bathtub in your washroom if you have actually already purchased a new bathtub as well as do not need to change the setup of your previous water system pipes.
Your devices and product checklist need to make up the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a fabric prepared for the staying water that will come from the pipelines. As soon as the supply pipelines have been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from transforming throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Before moving on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washing machines are in place in between the tap as well as the sink. Protect the faucet in position with the supplier given backnut. As soon as the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Using both wood boards under its feet, place the bath tub in the required placement. The wood boards are practical in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the spirit level checks out level.
To mount faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the water and examine all joints and new pipework for leaks and tighten them if needed. Load the bathtub as well as additionally inspect the overflow outlet as well as the typical electrical outlet for leakages.
Finally, take care of the bath paneling as defined in the maker's instruction manual. Tiling as well as securing around the bath tub ought to wait until the bathtub has actually been used at the very least once as this will certainly settle it right into its last position.
Planning for the Installation
First of all, the supporting framework provided with the bath needs to be fitted (if needed) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to prevent strain on the tub.
Fit the flexible faucet ports to the bottom of both taps making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last placement.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a stiff seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing difficulties with wetness as well as feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and cartridges, and also are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in usage. The sealer can crack relatively early if you do not think about this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our part on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you so much for taking time to browse our piece. For those who enjoyed our article if you please make sure you remember to pass it around. I praise you for your time. Come back soon.
Get professional leak detection today. Report this page